A High-Flow MAF for the Mazda6i Airbox

This is an overview of how to modify the top portion of the Mazda 6i airbox for a slightly larger Mass Air Flow (MAF) sensor tube. The oversized MAF tube is sized to provide better air flow while minimizing the calibration error of the MAF sensor which has been shown to cause CEL faults in many aftermarket CAI products. This modification will be most beneficial if the intake resonator, lower baffle tray, and VAD flapper restrictions are eliminated from the stock intake. For more details on these mods, check out the 'how-to' section of the Mazda6tech.com web site.
tools1.jpg

Besides basic tools, you will need a sharp razor knife, an electric drill, and a dremel along with the sanding and cutting bits shown above.
new MAF pic1
The first step is to fabricate a slightly oversized MAF tube to replace the stock tube in the top portion of the airbox. A section from a heavy 16 Oz. unbreakable plastic tumbler provides the right material for the MAF tube. The finished tube will be 4 1/2" long with an inlet diameter of 2 3/4" and an outlet diameter of about 2 5/8". This is just slightly larger than the stock MAF tube (ID=2.5"), but provides approximatly 9% more airflow area. (5.4 Sq In. vs 4.9 Sq In.) Note that the stock MAF sensor is reused in the new tube.
m6maf3.jpg
The next step is to cut the stock MAF tube out of the airbox cover. First remove the airbox cover from the car by disconnecting the MAF sensor, and the accordian tube and then rotate the cover just past verticle to release the hinge from the bottom of the box. Once the cover is on the bench, use a dremel cutting bit to slice the MAF tube out of the cover. A 3/32" drill and razor blade were used for the lower arch where the cutting bit would not reach.
m6abox1.jpg
Once the MAF tube is cut out, smooth out the cuts and expand the radius of the arcs to match the oversized MAF tube. Note that there are four basic cuts needed: One along both sides of the tube, and one across the top and bottom arch where the tube meets the airbox lid. The above picture shows the location of the four cuts.
m6abox3.jpg
Next, fit the new MAF tube into the airbox. A flapper sanding wheel and a file are helpful in trimming the cutout to fit for the new MAF tube. Once a good fit is obtained, secure the new tube in place with JB Weld epoxy. If you're using a quick-dry epoxy, work with several small batches instead of trying to seal up all the seams at once. The epoxy sets up quickly and won't flow smoothly into the seams if it's too hard.
m6abox4.jpg
After all the seams are filled with epoxy and dry, clean up the airbox lid and give it a coat of black paint for uniform color and a 'stock' appearance. Krylon's 'Fusion' paint is great for plastic and dries in about 30-40 minutes.
m6abox6.jpg
Reinstall the MAF sensor and replace the modified airbox lid on your air filter box.  The accordian tube will be a little tight over the MAF tube but will stretch with a little persuasion. A thin film of oil will ease the fitting. Plug in the MAF sensor and snug up the clamps.
Upon starting the car, you should see your idle drop to the usual 750 RPM after a few seconds. The idle  should remain stable, but may 'hunt' occasionally during the first drive cycle. Overall I have not experienced any drivability issues or CELs in the initial testing. The benefits are readily apparent in both low end grunt and a new willingness to build revs when you lean on the throttle.

This is not an easy or quick mod to perform but it will allow your airbox to provide the airflow benefits of an aftermarket CAI while preserving a more factory sound.  If you've removed the basic restrictions on your stock Mazda6i intake, this modification will take full advantage of the extra air flow capacity and give your 2.3L Duratec a more aggressive attitude.
*    Scott Burton      August 2004   *